Flintec MCS-08 Manual de usuario Pagina 22
- Pagina / 52
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MCS-08 Technical Manual, Rev. 1.04 December 2012 Page 22 of 52
4. Now change the address number on the Gateway Module by pressing the gateway switch (YELLOW) until it
reached an address you want to use for an MCS08AD or MCS08IO module.
5. To assign the selected address number to an A/D Converter or Digital I/O module press the setup switch on
the selected module (BLUE).
Please note: The MCS08 allows up to 8 A/D and 8 I/O in one system. A/Ds and I/Os
use the same address range (0 to 7). In consequence the same address can be
assigned to one A/D Converter AND one Digital I/O Module.
6. After assigning all modules to a defined address, press and hold the gateways switch for 5 seconds. The
system will close the addressing mode and change to normal mode
Note: Do not de-energise MCS-08 while the system is in the addressing mode. If a power failure has
happened, restart the system and repeat the whole addressing.
LED and Setup Switch Descriptions in the N-Bus Addressing Mode:
Gateway module
Description of LED
Description of Setup Switch
Pwr
Lnk
Err
Address number is [0]
Increase to address number [1]
Address number is [1]
Increase to address number [2]
Address number is [2]
Increase to address number [3]
Address number is [3]
Increase to address number [4]
Address number is [4]
Increase to address number [4]
Address number is [5]
Increase to address number [6]
Address number is [6]
Increase to address number [7]
Address number is [7]
Jump to address number [0]
Address number is higher than [7]
MCS-08AD or MCS-08IO
Description of LED
Description of Setup Switch
Err
Defined N-bus address number and
gateway‟s selected address number
are identical
Assigns the gateway‟s selected address
number to its N-bus address number.
Defined N-bus address number and
gateway‟s selected address number
are different
Increase to address number [2]
Off On Flash
Table 5.2 – N-bus addressing via setup switch
5.9. Back up Settings and Calibration Data
The parameter settings and the calibration coefficients can be saved to a backup file after reading these data
from the MCS-08 modules. This backup file can be re-written to MCS-08 modules after opening it by xFace.
The backup feature gives a service advantage to MCS-08 systems. We propose to burn these files to CD /
DVD and save this backup CD / DVD in the control cabinet additionally to a backup file on your PC.
Important note: The previous parameter settings and calibration coefficients in a MCS-08 module will get lost
after loading a backup to this module.
- Technical Manual 1
- RIGHTS AND LIABILITIES 3
- 1. SAFETY INSTRUCTIONS 4
- EG-Konformitätserklärung 5
- EC-Declaration of Conformity 5
- 3. INTRODUCTION 6
- 3.2. Specifications 7
- 3.3. Housing 9
- 3.4. Accessories 10
- 4. INSTALLATION 11
- 4.2. Electrical Connections 12
- 4.3. Commissioning 13
- 5. SETUP 14
- 5.3. N-Bus Addressing 15
- 5.4. Gateway Setup 16
- 5.5.1. Scale Parameters 17
- Auto Zero Tracking 18
- Save Tare at Power Off 18
- Mode selection 18
- Scale Build 19
- Calibration by Test Weights 19
- Zero Adjustment 19
- Span Adjustment 20
- Span Adjustment under Load 20
- 5.7. Digital I/O Test 21
- Not In Use 29
- – A/D CONVERTER MODULE 33
- 6.2. Electrical Connections 34
- 6.3. Setup and Calibration 34
- – DISPLAY MODULE 35
- – DIGITAL I/O MODULE 36
- – MODBUS RTU GATEWAY 37
- 9.2. Electrical Connections 38
- 9.3. N-Bus Addressing 38
- 9.4. Modbus RTU Setup 38
- – PROFIBUS GATEWAY 40
- 10.2. Electrical Connections 41
- 10.3. N-Bus Addressing 42
- 10.4. Profibus Setup 42
- – PROFINET GATEWAY 43
- 11.3. N-Bus Addressing 45
- 11.4. ProfiNet Setup 45
- – ETHERNET GATEWAY 46
- Ethernet Connector (RJ45) 47
- RS-232C Serial Interface 47
- Ethernet Interface 47
- 12.3. N-Bus Addressing 48
- 12.4. Ethernet Setup 48
- 13. ERROR TABLE 49
- 14. DIAGNOSTICS 50
- REQUENTLY ASKED QUESTIONS 51
Relacionado con productos y manuales para Hardware Flintec MCS-08
Hardware Flintec MCS-64 CANbus Manual de usuario
(62 paginas)
(62 paginas)
Hardware Flintec LDU 68.2 Manual de usuario
(28 paginas)
(28 paginas)
Hardware Flintec LDU 69.1 Manual de usuario
(28 paginas)
(28 paginas)
Hardware Flintec LDU 78.1 Manual de usuario
(36 paginas)
(36 paginas)
Hardware Flintec KAL-4 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KA-1 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec FAD-4 Manual de usuario
(26 paginas)
(26 paginas)
Hardware Flintec FDT-B Manual de usuario
(23 paginas)
(23 paginas)
Hardware Flintec KAK-4 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KA-6 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KEK-4 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KPK-4 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KP-4 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KPF-10 Manual de usuario
(8 paginas)
(8 paginas)
Hardware Flintec KAEX-4 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KEEX-4 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KPEX-10 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KPFD-8 Manual de usuario
(4 paginas)
(4 paginas)
Hardware Flintec KPB-4 Manual de usuario
(4 paginas)
(4 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales